xiao

PCB and PCBA A PCB (Printed Circuit Board) is a board that electrically connects electronic components using conductive traces, pads, and other features etched from copper foil laminated onto a non-conductive substrate. PCB’s can be  single sided  (one copper layer),  double sided  (two copper layers), or  multi-layer  (outer and inner layers). Conductors on different layers are connected with vias (plated-thru. holes). Multi-layer PCB’s allow for much higher component density and design complexity. PCBA (Printed Circuit Board Assembly) is the board obtained after all printing solder paste on the PCB and then mounting various components like resistors, ICs (Integrated Circuits), capacitors and any other components  like transformers depending on the application and desired characteristics of the board. A PCBA usually undergoes reflow furnace heating to establish a mechanical connection between the PCB and the components.

Requirements of power layer, stratigraphic partition and flow-hole:     Juvtmall  ( a company supply  PCB Prototyping ,  PCBA service  and sell kinds of  components, modules  and so on)  For PCB multilayer, there is at least one power layer and one layer. Because of all the voltage on the PCB are in the same power level, so you have to partition the isolation of power supply layer, the size of the partition line generally USES 20 ~ 80 mil line width advisable, ultra-high voltage, the more coarse partition line. In order to increase the reliability of the welding hole and the power supply layer and the stratigraphic connection, it is necessary to design the shape of the flower hole to reduce the large area metal heat absorption in the welding process The aperture of the isolation pad is greater than that of borehole aperture +20mil Requirements for safe spacing The setting of safety spacing should meet th...

Juvtmall  ( a company supply  PCB Prototyping ,  PCBA service  and sell kinds of  components, modules  and so on)  Motor shield  is a platform for robotics and mechanical applications based on L298P. It can be used to drive double DC motor or a 4-wire stepper. When controlling double DC motor, there are Only 4 control pins are used, which makes more easily to control, and saves the control pins for controller. The Drive current can be up to 2A per motor output for the adding of the heat sink. Measure the driver current by the additional resistance, makes the system more smartly. 

The requirements of wire cloth and wiring   Juvtmall  ( a company supply  PCB Prototyping ,  PCBA service  and sell kinds of  components, modules  and so on)  In general, PCB multilayer board wiring is performed according to circuit function. In outer wiring, it is required to have a lot of wiring in the welding surface, and the components are less wiring, which is beneficial to the maintenance and platoon of printing plate. Thin, tight conductor and easily disturbed signal lines, usually arranged in the inner layer. The large area of copper foil should be evenly distributed in the outer layer, which will help to reduce the warping of the plate and make the plating more uniform on the surface. In order to prevent the short circuit between the surface and the printed wire and the mechanical processing, the distance of the conductive graph in the inner and outer layers should be greater than 50mil. Wire direction and line widt...

RMF69 Shield-433MHz contains a FSK wireless module, it has the same function that radio frequency transmitter owns, such as receiving and transmitting message. RMF69 Shield-433MHz can totally compatible to Arduino. Features Low consumption More professional ISM band Frequent range from 140 to 960MHz  Totally compatible to Arduino http://juvtmall.com/rfm69-shiled_p0808.html

6. Basic requirement of designing multiple layer PCB       Juvtmall  ( a company supply  PCB Prototyping ,  PCBA service  and sell kinds of  components, modules  and so on)  Determine out shape, size, layers. Any plate, there are problems with other structural parts, so the shape and size of the printing plate must be based on the product machine structure. However, in terms of production process, it should be as simple as possible, generally for the long width ratio not too wide of the rectangle, to facilitate assembly, improve production efficiency, lower labor cost. The number of layers must be based on the circuit performance, the size of the plate and the intensity of the line. In the case of PCB multilayer, the application of four layers and six laminates is the most widely used, with four layers as an example, which is two conductor layers (surface and welding surface), a power supply layer and a layer. Th...

Juvtmall  ( a company supply  PCB Prototyping ,  PCBA service  and sell kinds of  components, modules  and so on)  The SIM808 GPRS/GSM+GPS Shield V1.0 is based on the chip named SIM808, it communicates with Catduino Uno via pins (RX, TX) with GPS data and GPRS data. For the operate voltage could either at 3.3V or 5V, it can be totally compatible to the Arduino. It can be also used to making/answering call, sending/receiving SMS messages and local the position. By the way, SIM GPRS/GSM+GPS Shield V1.0 suppose an SIM card holder at the opposite side. http://juvtmall.com/sim808-btgsmgps-sheild_p0813.html

  Juvtmall  ( a company supply  PCB Prototyping ,  PCBA service  and sell kinds of  components, modules  and so on)  Here, you can know the details:  http://juvtmall.com/simduino_p0814.html Contact me: ann@juvtmall.com

2.  Method of wiring on multiple layers PCB       Juvtmall  ( a company supply  PCB Prototyping ,  PCBA service  and sell kinds of  components, modules  and so on)     Generally, four layers board can be divide into top layer, bottom layer and two internal layer. Internal layer: by command “DESIGN/LAYER STACK MANAGER” use “ADD PLANE” add “INTERNAL PLANE1” and “INTERNAL PLANE2” as VCC and GND in power and GND layer (tip: don’t use “ADD LAYER”, it will add MIDPLAYER, it’s used in multiple layer of signal track), if there are several power layer such as VCC2 or GND layer such as GND2, then use bolder wire or FILL to draw a district on power of GND belongs to PLANE1 or PLANE2,  use PLACE/SPLIT PLANE to make a corresponding district (VCC2 copper and GND2 copper flakes are not present in this area in the same PLANE) tip: different surface layers in the same PLANE and try not to overlap.SPLIT1 and SPLIT2 are overlappe...